使用
自動攪拌車一體車時,有排水步驟,如何正確排水?讓我們來看看。
When using the automatic mixer truck, there are drainage steps. How to drain water correctly? Let's see.
啟動自動攪拌車一體車和液壓系統,以便將泵獲得的動量用于驅動液壓馬達。排水泵幾乎自動啟動,切換到清潔狀態,并準備控制操作按鈕。排出水箱中的水,打開水箱底部的排水球閥,然后等待水箱中的水排出。按下排水系統按鈕,并觀察泵出口的狀況。當供水停止從泵出口流出時,操作完成,泵中的水完全排干。
Start the all-in-one truck and hydraulic system of the automatic mixer to use the momentum obtained by the pump to drive the hydraulic motor. The drainage pump starts almost automatically, switches to the clean state, and prepares to control the operation button. Drain the water in the tank, open the drain ball valve at the bottom of the tank, and then wait for the water in the tank to drain. Press the drain system button and observe the condition of the pump outlet. When the water supply stops flowing from the pump outlet, the operation is completed and the water in the pump is completely drained.
根據以上過程,自動攪拌車一體車的泵排干干凈,冬天不怕泵開裂。請注意,每次使用泵時,都必須將其排干。否則,它將在一夜之間被完全損壞,將無法使用。另外,在自動攪拌車一體車的強制排水過程中,必須注意泵的出口。
According to the above process, the pump of the automatic mixer truck is drained completely, and the pump is not afraid of cracking in winter. Please note that the pump must be drained every time it is used. Otherwise, it will be completely damaged overnight and will be unusable. In addition, attention must be paid to the outlet of the pump during the forced drainage process of the automatic mixer truck.
如何保持自動攪拌車一體車的漆面
How to keep the paint surface of automatic mixer truck
1.如果不使用自動攪拌車一體車的涂漆表面,則金屬涂層會產生非常細的裂紋,并會繼續滲透涂層,直到其滲透到整個涂層為止。如果裂紋中包含蠟,則身體上會出現條紋。定期打蠟可以逐漸減少裂紋。
1. If the painting surface of the all-in-one truck of the automatic mixer is not used, the metal coating will produce very fine cracks and will continue to penetrate the coating until it penetrates the whole coating. If the cracks contain wax, streaks appear on the body. Regular waxing can gradually reduce cracks.
2.自動攪拌車一體車在暴露于陽光的紫外線下會蒸發并保護空氣中的油,隨著時間的流逝,涂料會過度分散。油漆表面的亮度和深度大大降低,油漆表面逐漸變白,形成氧化層,縮短了油漆壽命。如果自動攪拌車一體車的油漆表面被嚴重氧化,則可以通過研磨和拋光對其進行處理。
2. The all-in-one truck of automatic mixer will evaporate and protect the oil in the air when exposed to the ultraviolet rays of sunlight. As time goes by, the coating will be excessively dispersed. The brightness and depth of the paint surface are greatly reduced, and the paint surface gradually turns white, forming an oxide layer, which shortens the paint life. If the paint surface of the automatic mixer truck is seriously oxidized, it can be treated by grinding and polishing.
3.由于自動攪拌車一體車,表面發生磨損。可能是昆蟲,鳥糞,樹汁,柏油和瀝青所致。一些小的蝕刻可以通過研磨和拋光。
3. The surface of the automatic mixer is abraded. It may be caused by insects, bird droppings, tree sap, tar and asphalt. Some small etching can be done by grinding and polishing.
除了上述方法之外,為了有效地防止油漆濺到車輛上,在駕駛時必須注意駕駛并避免碰撞和摩擦。否則會發生其他損壞。
In addition to the above methods, in order to effectively prevent paint splashing on the vehicle, it is necessary to pay attention to driving and avoid collision and friction. Otherwise, other damage may occur.
自動攪拌車一體車的排水作業和維護車漆表面了解就是這樣,你學會了嗎?
Drainage operation and maintenance of automatic mixer truck paint surface understanding is like this, have you learned it?