即使長期使用機械設備——自動攪拌一體機,也要不時潤滑以保持良好的運行性能。那么,在向設備中添加潤滑劑時需要注意什么?
Even if long-term use of mechanical equipment - automatic mixing machine, but also from time to time lubrication to maintain good performance. So what do you need to pay attention to when adding lubricant to the equipment?
1.在操作過程中,切勿對自動電源混合器進行大修和潤滑。
1. Never overhaul or lubricate the automatic power mixer during operation.
2.定期潤滑每個注油嘴,每4小時給軸端密封圈注脂一次,并每周排放一次污水。
2. Lubricate each oil nozzle regularly, grease the shaft end sealing ring every 4 hours, and discharge sewage once a week.
3.使用自動攪拌車后,根據需要在每個潤滑點添加所需的潤滑油(輥軸,輥,鋼絲繩和其他運動部件)。
3. After using the automatic mixer, add the required lubricating oil (roller shaft, roller, wire rope and other moving parts) at each lubricating point as required.
4.自動攪拌一體機減速器的齒輪箱的齒輪和軸承利用齒輪的旋轉將油濺到箱內壁上,并流入軸承中進行潤滑。變速箱中的油位應保持在油尺上的兩條刻線之間。如果油位太高或太低,則每個零件的溫度都會升高,潤滑會不足,從而導致功率損耗增加,機器運行速度變慢。
4. The gear and bearing of the gearbox of the automatic mixing all-in-one machine make use of the rotation of the gear to splash the oil on the inner wall of the gearbox and flow into the bearing for lubrication. The oil level in the transmission should be maintained between the two lines on the dipstick. If the oil level is too high or too low, the temperature of each part will rise and the lubrication will be insufficient, which will lead to the increase of power loss and the slow running speed of the machine.
5.為自動攪拌一體機選擇的潤滑油必 須具有特定的粘度和粘度-溫度特性,低凝固點,良好的氧化穩定性,無機械雜質和濕氣,腐蝕和磨損材料。有。其質量指標必 須符合標準。
5. The lubricating oil selected for the automatic mixer must have specific viscosity and viscosity temperature characteristics, low freezing point, good oxidation stability, no mechanical impurities and moisture, corrosion and wear materials. yes. Its quality index must conform to the national standard.
自動攪拌一體機是為了有用減少磨損并提高組件的使用壽命。但是,添加潤滑油時要小心。新機器每前150和300小時應更換一次機油,以清 除調試期間未完 全清 除的污垢。在工作時要經常檢查油位,以彌補您的時間不足。
The purpose of the automatic mixer is to reduce wear and improve the service life of components. However, be careful when adding lubricating oil. The oil of new machine should be changed every 150 and 300 hours to remove the dirt not completely removed during commissioning. Always check the oil level at work to make up for your lack of time.