完美世界txt下载,好看的玄幻小说,小说网

站內搜索

常見問題

熱點

自動上料平口攪拌機多種方量可供選擇

2022-12-23

混凝土自動上料攪拌車的功能有哪些？

2022-12-19

混凝土自動拌料車移動式可自行走戶外施工

2022-12-16

自上料攪拌車企業這么多，買車的時候應該看哪方面？

2022-12-12

關于山汽

聯系人：劉老師

電話：400-879-1999

公司：山東山汽工程機械（集團）有限公司

地址：山東省萊州市206國道與308省道交叉口東南50米

攪拌車有兩種校準螺旋電子秤的方法

所屬分類：常見問題發布時間：2021-06-23 來源：http://klalyy.cn/ 瀏覽量：0

多功能攪拌車皮帶秤的校準方法：將速度控制器上的“自動/手動”開關設置到手動位置，將速度調節到小電位器，打開主機和速度控制器的電源。15分鐘后，啟動皮帶秤，調節速度控制器上的速度，讓電位器使皮帶運轉（轉速400-500轉/分），根據需要測試零點。按F3鍵將光標移動到要校準的K值的前面，然后按F5鍵，在已知重量（累計重量大于100KG）的跑帶上放置一些沙袋。

Calibration method of multifunctional mixer belt scale: set the "auto / manual" switch on the speed controller to the manual position, adjust the speed to the small potentiometer, and turn on the power supply of the host and speed controller. After 15 minutes, start the belt scale, adjust the speed on the speed controller, let the potentiometer make the belt run (speed 400-500 RPM), and test the zero point as required. Press F3 to move the cursor to the front of the K value to be calibrated, and then press F5 to place some sandbags on the running belt with known weight (cumulative weight greater than 100kg).

從皮帶上完成代碼或沙袋后，按Enter鍵。此時，以流量顯示重量或沙袋的累積值，然后將重量或沙袋的重量發送到K值。道路的K值由微型計算機確定。計算新的K值并以相同的方式校準2-3次，直到累積流量等于實際流量。其他道路標記方法與上述相同。

After completing the code or sandbag from the belt, press enter. At this time, the cumulative value of weight or sandbag is displayed by flow, and then the weight or sandbag weight is sent to K value. The K value of the road is determined by a microcomputer. Calculate the new K value and calibrate 2-3 times in the same way until the cumulative flow equals the actual flow. Other road marking methods are the same as above.

校準方法在多功能攪拌車中有兩種校準螺旋電子秤的方法：將速度控制器上的“自動/手動”開關置于手動位置，將給定電位器的速度調較小，并且螺旋電子秤啟動。內部的水泥是干凈的，然后根據零測量方法測量零點。

Calibration methods there are two methods to calibrate the spiral electronic scale in the multi-function mixer: put the "auto / manual" switch on the speed controller in the manual position, adjust the speed of the given potentiometer to a smaller value, and start the spiral electronic scale. The cement inside is clean and then zero is measured according to the zero measurement method.

按F3鍵將光標移動到第七路K值的前面，按F5鍵調節送料器速度控制的速度，讓電位器旋鈕卸下，同時擰緊螺絲電子秤在排出口排出，水穩定?；旌险镜幕旌蠋瓿珊?，按Enter鍵，然后將物料的實際重量發送到K值。按Enter確認。這是K值自動生成一個新的K值，它以相同的方式校準。直到累計重量等于實際重量，校準完成。

Press the F3 key to move the cursor to the front of the seventh K value, press the F5 key to adjust the speed of the feeder speed control, so that the potentiometer knob can be removed, at the same time, tighten the screw, and the electronic scale discharges at the discharge outlet, so that the water is stable. When the mixing belt of the mixing station is finished, press enter, and then send the actual weight of the material to K value. Press enter to confirm. This is the K value that automatically generates a new K value, which is calibrated in the same way. The calibration is completed until the cumulative weight equals the actual weight.

多功能攪拌車水的校準方法：由于系統采用水表，即高精度電子測量水表，水的校準簡單。重要的是將對應于每千克水的水表的脈沖量發送到第九道路的K值。

Multi function mixer water calibration method: because the system uses water meter, that is, high-precision professional electronic measuring water meter, water calibration is simple. It is important to send the pulse quantity of the water meter corresponding to each kilogram of water to the K value of the ninth road.

上一頁：2方自動攪拌一體車的故障方式！下一頁：自動攪拌一體車罐子不轉是哪出問題了？

熱門產品 / HOT PRODUCT