自動上料攪拌一體機這種機械設備需要不時進行潤滑,以便在長期使用時保持良好的操作性能。那么在為設備添加潤滑劑時應該注意什么呢?
This kind of mechanical equipment needs lubrication from time to time in order to maintain good operation performance in long-term use. So what should be paid attention to when adding lubricant to the equipment?
1.自動上料攪拌一體機在運行過程中不應進行修理和潤滑。
1. The automatic feeding and mixing machine should not be repaired and lubricated during operation.
2.定期在每個潤滑脂嘴上添加黃油,并在軸端密封處每4小時潤滑一次油,每周排水一次。
2. Regularly add grease to each grease fitting, lubricate the shaft end seal every 4 hours, and drain water once a week.
3.使用自動上料攪拌一體機后,根據需要在每個潤滑點添加必要的潤滑油(滾筒軸,滾筒,鋼絲繩和其他有效部件)。
3. After using the automatic feeding and mixing machine, add necessary lubricating oil (drum shaft, drum, wire rope and other effective parts) at each lubricating point as required.
4.自動上料攪拌一體機減速機的齒輪和軸承使用齒輪旋轉將油濺入油箱內壁并流入軸承進行潤滑。變速箱的油位應保持在油量計的兩條線之間。油位過高或過低都會導致各部件溫度升高或潤滑不良,增加動力損失并導致機器運行不良。
4. The gears and bearings of the reducer of the automatic feeding and mixing machine splash oil into the inner wall of the oil tank and flow into the bearing for lubrication. The oil level of the gearbox should be maintained between the two lines of the oil gauge. If the oil level is too high or too low, the temperature of each part will rise or the lubrication will be poor, which will increase the power loss and lead to the poor operation of the machine.
5.自動送料攪拌機選用的潤滑油應具有一定的粘度和粘溫特性,低凝固點,良好的氧化穩定性,無機械雜質和水分,無腐蝕和耐磨材料。其質量指標應符合標準。
5. The lubricating oil selected by the automatic feeding mixer should have certain viscosity and viscosity temperature characteristics, low freezing point, good oxidation stability, no mechanical impurities and moisture, no corrosion and wear-resistant materials. The quality index should meet the national standard.
上料攪拌一體機用于潤滑,減少磨損,提高部件的使用壽命。但是,在添加潤滑油的過程中需要注意一些事項。新機器應在初150小時和300小時內更換一次,以測試期間未完全清潔的污垢。工作時,請務必檢查油位,并及時添加。
The feeding and mixing machine is used for lubrication, reducing wear and improving the service life of components. However, in the process of adding lubricating oil, we need to pay attention to some matters. The new machine should be replaced once in the first 150 hours and 300 hours to remove dirt that was not completely cleaned during the test. When working, please check the oil level and add it in time.
自動上料攪拌一體機關于添加潤滑油的問題就是這樣了,希望對你有幫助。如有更多疑問可以關注公司網站:http://klalyy.cn后續會有更多的內容呈現。
Automatic feeding and mixing machine about the problem of adding lubricating oil is like this, hope to help you. For more questions, please visit the company's website: http://klalyy.cn More content will be presented later.