如果自動攪拌一體車在使用過程中出現防鎖系統故障,將影響攪拌車的正常運行。但是,如果自動上料攪拌車的防抱死系統出現故障,必須及時,否則會影響施工效率。如何檢查自動攪拌一體車的防抱死系統?
If the automatic mixer truck in the process of using the anti lock system failure, it will affect the normal operation of the mixer truck. However, if the anti lock system of automatic feeding mixer fails, it must be solved in time, otherwise it will affect the construction efficiency. How to check the anti lock system of automatic mixer truck?
1.檢查攪拌車的停車制動器是否完全松動。
1. Check whether the parking brake of the mixer is completely loose.
2.檢查攪拌車的制動罐液位是否符合本手冊的要求。
2. Check whether the liquid level of the brake tank of the mixer meets the requirements of this manual.
3.檢查攪拌車的所有制動管路是否有損壞和泄漏跡象。
3. Check all brake pipes of mixer for damage and leakage.
4.檢查防抱死系統中的所有保險絲是否完好,電線是否損壞,以及插座是否牢固。
4. Check whether all fuses in anti lock system are in good condition, whether wires are damaged, and whether sockets are firm.
5.檢查電池容量和電壓是否符合要求,以及正負極線之間的連接是否可靠。
5. Check whether the battery capacity and voltage meet the requirements, and whether the connection between the positive and negative wires is reliable.
6.檢查防抱死系統和ECI_I連接器是否牢固連接。
6. Check anti lock system and ECI_ Whether the I connector is firmly connected.
7.檢查電路連接是否有腐蝕,損壞,松動或接觸不良。ABS的每根接地線的接地是否可靠。
7. Check the circuit connection for corrosion, damage, looseness or poor contact. Whether the grounding of each grounding wire of ABS is reliable.
8.檢查輪胎是否符合要求。
8. Check whether the tire meets the requirements.
9.檢查自動上料攪拌車的輪子是否轉動,輪轂的軸承間隙是否正常。
9. Check whether the wheels of the automatic feeding mixer rotate and whether the bearing clearance of the hub is normal.
自動攪拌一體車的程序
Safety procedure of automatic mixer truck
1.在駕駛之前,您必須仔細檢查車輛的狀況,以確保車輛能夠駕駛。
1. Before driving, you must carefully check the condition of the vehicle to ensure that the vehicle can drive safely.
2.當自動上料攪拌車停放在露天時,攪拌桶應在裝料前翻轉,并應排出積聚的水和碎屑,以確保混凝土的質量。
2. When the automatic feeding mixer is parked in the open air, the mixing bucket shall be turned over before loading, and the accumulated water and debris shall be discharged to ensure the quality of concrete.
3.運輸混凝土?xí)r,確保傾斜槽牢固放置,防止因松動而擺動,行人在行駛中受傷或影響其他車輛的正常運行,同時注意避免混凝土溢出和污染地面。
3. When transporting concrete, ensure that the inclined slot is firmly placed to prevent swinging due to looseness, pedestrian injury during driving or affecting the normal operation of other vehicles, and pay attention to avoid concrete overflow and ground pollution.
4.自動上料攪拌車不應運輸混凝土超過攪拌站規定的時間。在運輸混凝土的途中,攪拌筒不應長時間停止,以防止混凝土的分離。駕駛員應始終注意具體情況,并在發現異常時通知主控室,并申請。
4. The automatic feeding mixer shall not transport the concrete beyond the time specified by the mixing plant. During the transportation of concrete, the mixing drum should not be stopped for a long time to prevent the separation of concrete. The driver should always pay attention to the specific situation and inform the main control room when finding any abnormality and apply for treatment.
5.當混凝土安裝在車內時,現場的停滯時間不得超過1小時。如果超時,應要求現場負責人及時處理。
5. When the concrete is installed in the vehicle, the dead time on site shall not exceed 1 hour. In case of overtime, the person in charge of the site shall be required to deal with it in time.
自動上料攪拌車的防抱死系統以及程序介紹就是這樣了,希望對你有幫助
Automatic feeding mixer anti lock system and safety procedures is like this, I hope to help you